Siemens interranger DPS300 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 111

Siemens interranger DPS300 Скачать руководство пользователя страница 51

7ML19981BC01

51

InterRanger

DPS300

System Performance Evaluation

For initial RUN mode entry (or after any programming alteration), do not use the
DPS300 to operate process control equipment until satisfactory system
programming and performance is verified.

1. Press to enter the RUN mode.

“----” may be displayed briefly while the DPS300 takes measurements and
calculates the Reading.

If an alarm symbol is displayed, the corresponding relay is de-energized.

POINT #

ALARM INDICATOR

RELAY #

1 High

Alarm

1

1 Low

Alarm

2

2 High

Alarm

3

2 Low

Alarm

4

2. Press to display Readings in

%

(percent of Span, P007) based upon Operation

(P001).

OPERATION

LEVEL

SPACE, or DISTANCE*

Empty to Full =

0 to 100%

100 to 0%

* Objects close to the transducer face (0%) are not detectable.

3. Press to observe the mA output value for the Point Number displayed

(Auxiliary Reading).

OPERATION

LEVEL

SPACE, or DISTANCE*

Empty to Full =

4-20 mA

20-4 mA

* Objects close to the transducer face (4 mA) are not detectable.

4. Press to observe the

Failsafe Time Left

(time left in percent before failsafe

activation).

Each time a valid measurement is made for the Point Number displayed, this
value (Auxiliary Reading) is reset to 100 and begins to fall toward 0 until the next
valid measurement is made.

If the Failsafe Time Left reaches 0, the DPS300 flashes “LOE” in the Reading
display.

All associated data is supplied to the Peripheral Communications terminals (27
and 28). If a BIC-II is connected, refer to TECHNICAL REFERENCE /
Communication Support for message format and protocol information.

«
...
49
50
51
52
53
...
»

Содержание interranger DPS300
















































































































Отзывы:

Нет отзывов