manualshive.com logo in svg

Siemens interranger DPS300, Инструкция пользователя, Страница: 29 / 111

Поделиться
Скачать
Siemens interranger DPS300 Скачать руководство пользователя страница 29

 

7ML19981BC01 

29

 InterRanger 

DPS300

 

Optional Skimmer Guard 

The skimmer guard is designed for use with transducers applied to measurement 
of sludge in wastewater clarifiers. The guard provides articulation of the 
mechanical and electrical conduit connection to the transducer where skimmers 
are in use. 

As the skimmer passes, it contacts the skimmer guard and pushes it up and over 
the skimmer; effectively clearing the transducer out of harm’s way. Once the 
skimmer has passed, the guard is free to fall, re-immersing the transducer into the 
clarifier water. 

The skimmer guard is available in two sizes: 

•

  Type A – for skimmers 20 cm (8”) or less in cross-sectional height 

•

  Type B – for skimmers 40 cm (16”) or greater in cross-sectional height 

 

conduit coupling,

¾

” NPT or BSP

hinge

boot

transducer coupling,

1” NPT or BSP

guard

Type A: 

500 mm (20”) 

97 mm 

(3.8”) 

100 mm 

(4”) 

200 mm 

(8”) 

Type B: 

890 mm (35”) 

Содержание interranger DPS300
















































































































Отзывы:

Нет отзывов