Siemens 7ML5430 Скачать руководство пользователя страница 5

Страница: 5 / 111

Table of contents

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

P069 Unlocked value .............................................................................................................. 51

7.17

Failsafe (P070 to P073) .......................................................................................................... 52

7.17.1

P070 Failsafe timer ................................................................................................................. 52

7.17.2

P071 Failsafe material level .................................................................................................... 52

7.17.3

P073 Failsafe level .................................................................................................................. 52

7.18

mA output (P201 to P215) ...................................................................................................... 53

7.18.1

P201 mA Output function ........................................................................................................ 53

7.18.2

Independent mA setpoint parameters (P210 and P211) ........................................................ 53

7.18.2.1

P210 4 mA setpoint (low output) ............................................................................................. 54

7.18.2.2

P211 20 mA setpoint (high output) ......................................................................................... 55

7.18.3

mA output limit parameters (P212 and P213) ........................................................................ 55

7.18.3.1

P212 Minimum mA limit .......................................................................................................... 55

7.18.3.2

P213 Maximum mA limit ......................................................................................................... 55

7.18.4

P214 4 mA output trim ............................................................................................................ 56

7.18.5

P215 20 mA output trim .......................................................................................................... 56

7.19

Installation records (P341 to P346) ........................................................................................ 56

7.19.1

P341 RUN time ....................................................................................................................... 56

7.19.2

P342 Power-on resets ............................................................................................................ 57

7.19.3

P343 Internal temperature ...................................................................................................... 57

7.19.4

P346 Serial number ................................................................................................................ 57

7.20

Range calibration (P652 to P655) ........................................................................................... 57

7.20.1

P652 Offset correction ............................................................................................................ 58

7.20.2

P655 Propagation factor ......................................................................................................... 58

7.21

Rate (P700 and P701) ............................................................................................................ 59

7.21.1

P700 Maximum fill rate ........................................................................................................... 59

7.21.2

P701 Maximum empty rate ..................................................................................................... 59

7.22

Measurement verification (P709 to P713) .............................................................................. 60

7.22.1

P709 Damping filter ................................................................................................................ 60

7.22.2

P711 Echo lock ....................................................................................................................... 60

7.22.3

P712 Echo lock sampling ....................................................................................................... 61

7.22.4

P713 Echo lock window .......................................................................................................... 62

7.23

P752 HART address ............................................................................................................... 63

7.24

Communications (P799) ......................................................................................................... 63

7.24.1

P799 Communications control ................................................................................................ 63

7.25

Echo processing (P800 to P807) ............................................................................................ 63

7.25.1

P800 Near blanking ................................................................................................................ 64

7.25.2

P801 Range extension ........................................................................................................... 64

7.25.3

P804 Confidence threshold .................................................................................................... 64

7.25.4

P805 Echo confidence ............................................................................................................ 65

7.25.5

P806 Echo strength ................................................................................................................ 65

7.25.6

P807 Noise ............................................................................................................................. 65

7.26

Algorithm (P820) ..................................................................................................................... 65

7.26.1

P820 Echo algorithm............................................................................................................... 65

7.27

TVT (Time Varying Threshold) adjustment parameters (P831 to P839) ................................ 66

7.27.1

P831 Manual TVT Shaper ...................................................................................................... 66

7.27.2

P832 Manual TVT Shaper Adjust ........................................................................................... 66

7.27.3

P837 Auto false echo suppression ......................................................................................... 66

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 5 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: