Siemens 7ML5430 Скачать руководство пользователя страница 48

Страница: 48 / 111

Parameter assignment

7.11 P051 Maximum volume

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

P050

Value

Vessel shape

Description

Also required

sphere

P051

universal linear level/volume break-

points

P051, P054, P055

7.11

P051 Maximum volume

For readings in volumetric units instead of percentage values, enter the vessel volume

between Empty (P006) and Span (P007). Any volumetric units can be chosen, because the

volume calculation is based on the maximum volume, and scaled according to the Vessel

Shape (P050) value. If no value is entered, the default is 100, and the reading will be a

percentage value.

Values

Range

0.0000 to 99999

Default

100.0

Related parameters

P006 Empty
P007 Span

Enter the vessel volume between Empty (P006) and Span (P007).
1.

Key in the value. (For example, if maximum volume = 3650 m

, key in 3650.)

Press ENTER

If the value is too large for the LCD display, enter larger units.
Example: If maximum volume = 267,500 gallons, key in 267.5 (thousands of gallons).

7.12

P052 Vessel dimension A

Dimension A as used for P050 Vessel Shapes 2, 3, 4, 5, or 7, in P050 Vessel shape

(Page 46).

Values

Range

0.0000 to 99999 in units (P005)

Default

0.0

Related parameters

P050 Vessel Shape

Enter one of the following, using the units selected in P005:

●

Height of the vessel bottom if P050 = 2, 3, 4, or 5

●

Length of one end-section of the vessel if P050 = 7

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 48 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: