Siemens 7ML5430 Скачать руководство пользователя страница 70

Страница: 70 / 111

Parameter assignment

7.29 Measurement

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

7.29.2

P920 Reading measurement

P920 corresponds to the final reading after all programming is applied. It is a copy of one of

P921 to P924, depending on the setting for Operation (P001).

Operation P001

Source parameter for P920

Off

----

Level

P921 if P050 = 0, otherwise P924

Space

P922

Distance

P923

P920 Values (read only)

Range

–99999 to 99999 (dimensional units, if volume has not

been selected)

7.29.3

P921 Material measurement

Displays the distance between Empty/process empty level (P006) and the monitored

surface, in Units (P005) or percent of Span (P007).

Values (view only)

Range

–99999 to 99999

7.29.4

P922 Space measurement

Displays the distance between the monitored surface and Span / process full level (P007).

Values (view only)

Range

–99999 to 99999

7.29.5

P923 Distance measurement

Displays the distance between the monitored surface and the reference point. For the

reference point for the standard model, see SITRANS Probe LR dimensions (Page 84).

Values (view only)

Range

–99999 to 99999

7.29.6

P924 Volume measurement

Note
The display for P924 reads - - - -, when volume calculation is not enabled at P050 (P050 =

0).

The calculated vessel capacity in Maximum Volume (P051) or percent of Maximum Volume

(volume calculation must be enabled at P050).

Values (view only)

Range

–99999 to 99999

Related parameters

P051 Maximum volume
P050 Vessel shape

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 70 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: