Siemens 7ML5430 Скачать руководство пользователя страница 63

Страница: 63 / 111

Parameter assignment

7.23 P752 HART address

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

7.23

P752 HART address

Note
Accessible via the handheld programmer only by keying in P752.

Sets the device address or poll ID on a HART network. Any address other than 0 will cause

the output current to be a fixed value, and the current will not indicate the reading.

Values

Range

0 to 15 Enter 0 for single transmitter installation; enter digit

other than 0 for multi-drop applications. (Default: 0)

7.24

Communications (P799)

7.24.1

P799 Communications control

Enables the read/write access to parameters via remote communications.

Values

Read only

Read/write

Restricted access - read only except for P799 which is read/write

Note

•

P799 controls the access if you are using a HART master.

•

P000 controls the lock access if you are using the Siemens handheld programmer.

7.25

Echo processing (P800 to P807)

Note
Factory settings are indicated by an asterisk (*) in the parameter tables, unless explicitly

described.

The following parameters are for authorized Siemens Service personnel or technicians

familiar with Siemens echo processing techniques. View the echo profile first, using

SIMATIC PDM, before attempting to modify these parameters.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 63 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: