Siemens 7ML5430 Скачать руководство пользователя страница 92

Страница: 92 / 111

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

HART communication

B.1

HART communication for SITRANS Probe LR

Highway Addressable Remote Transducer, HART, is an industrial protocol that is

superimposed on the 4-20 mA signal. It is an open standard, and full details about HART can

be obtained from HART Communication Foundation (

https://fieldcommgroup.org/

SITRANS Probe LR can be configured over the HART network using either a HART

handheld Communicator, or a software package. There are a number of different software

packages available. The recommended software package is the SIMATIC Process Device

Manager (PDM) by Siemens.

B.2

HART electronic device description (EDD)

Note
SITRANS Probe LR cannot be configured using a generic EDD.

In order to configure a HART device, the configurator must have the HART Electronic Device

Description for the device in question. HART EDD’s are controlled by the HART

Communication Foundation.
Please contact your local Siemens representative concerning the availability of the HART

EDD for SITRANS Probe LR. Older versions of the library will have to be updated in order to

use all the features in the SITRANS Probe LR.

B.3

SIMATIC process device manager (PDM)

This software package is designed to permit easy configuration, monitoring, and

troubleshooting of HART devices. The HART EDD for SITRANS Probe LR was written with

SIMATIC PDM in mind and has been extensively tested with this software.
The Device Description for SIMATIC PDM may be downloaded from the product page of our

website, under downloads.
Product page (

https://w3.siemens.com/mcms/sensor-systems/en/process-

instrumentation/level-measurement-with-level-measuring-

instruments/continuous/radar/Pages/sitrans-probe-lr.aspx

)

All parameters accessible via the HART Communicator are also accessible via PDM. In

addition, the Maintenance parameters listed below are accessible via PDM only.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 92 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: