Siemens 7ML5430 Скачать руководство пользователя страница 53

Страница: 53 / 111

Parameter assignment

7.18 mA output (P201 to P215)

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

7.18

mA output (P201 to P215)

Note
Factory settings are indicated by an asterisk (*) in the parameter tables, unless explicitly

described.

7.18.1

P201 mA Output function

Alters the mA output/measurement relationship, and allows the output to be set

independently from P001. If a HART master is connected, only the master can change the

value.

Values

manual

level

space

distance

volume (only available if a tank shape has been selected at P050)

Note

•

P201 is set independently from P001: set P001 first, as changing P001 will reset P201 to

the same setting.

•

P201 controls the primary value and the loop current for the HART common module and

should not be changed if using HART.

•

Selection also affects the secondary, tertiary, and quaternary variables for HART.

•

P201 must be set to 0 (manual) before you can modify P911. Remember to restore the

previous setting after using P911.

7.18.2

Independent mA setpoint parameters (P210 and P211)

P210 and P211 allow you to explicitly define the normal operating range. Use these features

to reference the minimum and/or maximum mA output to any point in the measurement

range.
For HART, 4 mA and 20 mA represent the upper and lower range limits for the primary

variable.

P201 (mA Function) Settings

Response for P210 and P211

Level, Space, or Distance

Key in the material level in Units (P005) or percent

of Span

(P007) as referenced from Empty (P006).

Volume

Key in the volume in Maximum Volume (P051) units or as a per-

cent

of Maximum Volume.

Ensure the % symbol is displayed before entering a % value.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 53 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: