Siemens 7ML5430 Скачать руководство пользователя страница 52

Страница: 52 / 111

Parameter assignment

7.17 Failsafe (P070 to P073)

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

7.17

Failsafe (P070 to P073)

Note
Factory settings are indicated by an asterisk (*) in the parameter tables, unless explicitly

described.

7.17.1

P070 Failsafe timer

Note
The last valid reading is maintained until the Failsafe timer expires. After the timer expires,

the reading is set based on P071.

Sets the time to elapse in minutes since the last valid reading, before Failsafe State

activates.

Values

Range

0.00 to 720 min.

Default

100.0 (based on P003)

7.17.2

P071 Failsafe material level

The material level to be reported when the Failsafe Timer expires. For more detail, see

Failsafe (Page 91).

Values

Use Maximum mA Limit (P213) as material level

Use Minimum mA Limit (P212) as material level

Level remains at last reading

User-selected value (defined in P073)

Enter the value corresponding to the level you want reported when the Failsafe Timer

expires.

Press ENTER

7.17.3

P073 Failsafe level

Note
P071 must be set to User-selected value (4) to use this value.

Defines a user-defined level to report when the Failsafe timer expires.

Values

Range

3.6 mA to 22.6 mA

Default

22.6 mA

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 52 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: