Siemens 7ML5430 Скачать руководство пользователя страница 93

Страница: 93 / 111

HART communication

B.4 Maintenance settings (accessible via PDM only)

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

B.4

Maintenance settings (accessible via PDM only)

Device lifetime

•

Total device operating time

•

Remaining device lifetime

•

Maintenance required limit

•

Maintenance demanded limit

•

Maintenance alert activation

•

Total expected device life

•

Units

•

Maintenance status

•

Acknowledge status

•

Acknowledge

Service interval

•

Time elapsed since last service

•

Maintenance required limit

•

Maintenance demanded limit

•

Maintenance alert activation

•

Total service interval

•

Units

•

Maintenance status

•

Acknowledge status

•

Acknowledge

Sensor lifetime

•

Total sensor operating time

•

Remaining sensor lifetime

•

Maintenance required limit

•

Maintenance demanded limit

•

Maintenance alert activation

•

Total expected sensor life

•

Units

•

Maintenance status

•

Acknowledge status

•

Acknowledge

Calibration interval

•

Time elapsed since last calibration

•

Maintenance required limit

•

Maintenance demanded limit

•

Maintenance alert activation

•

Total calibration interval

•

Units

•

Maintenance status

•

Acknowledge status

•

Acknowledge

B.5

HART version

SITRANS Probe LR conforms to HART rev. 5.

B.6

Burst mode

SITRANS Probe LR does not support burst mode.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 93 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: