Siemens 7ML5430 Скачать руководство пользователя страница 25

Страница: 25 / 111

Connecting

5.3 Nameplates for hazardous area installations

SITRANS Probe LR with mA/HART
Operating Instructions, 05/2019, A5E32337711-AC

Device nameplate (ATEX/IECEX/INMETRO/RMC)
The ATEX certificate can be downloaded from the product page of our website at:

www.siemens.com\sitransprobelr (

www.siemens.com\sitransprobelr

Go to Support > Approvals / Certificates.
The IECEx certificate listed on the nameplate can be viewed on the IECEx website. Go

to:http://iecex.iec.ch (

http://iecex.iec.ch

) and click on Ex Equipment Certificates of Conformity

then enter the certificate number IECEx SIR 13.0005X.

5.3.1

FM and CSA connection drawings

The FM Intrinsically Safe connection drawing (A5E01003040) listed on the device nameplate

can be downloaded from our website:
Product page (

www.siemens.com/ProbeLR

)

Go to Technical Info > Images, graphics, drawings.

The CSA Intrinsically Safe connection drawing (A5E01003039) listed on the device

nameplate can be downloaded from our website:
Product page (

www.siemens.com/ProbeLR

)

Go to Technical Info > Images, graphics, drawings.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 25 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: