Siemens 7ML5430 Скачать руководство пользователя страница 66

Страница: 66 / 111

Parameter assignment

7.27 TVT (Time Varying Threshold) adjustment parameters (P831 to P839)

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

7.27

TVT (Time Varying Threshold) adjustment parameters (P831 to

P839)

Note
Factory settings are indicated by an asterisk (*) in the parameter tables, unless explicitly

described.

First SITRANS Probe LR learns the echo profile. Then the learned profile, or part of the

learned profile, is used to screen out false echoes.
The following parameters are for authorized Siemens Service personnel or technicians

familiar with Siemens echo processing techniques. View the echo profile first, before

attempting to modify these parameters.

7.27.1

P831 Manual TVT Shaper

Note
This parameter is for use only by Siemens service personnel.

Turns the TVT Shaper ON or OFF.

7.27.2

P832 Manual TVT Shaper Adjust

Note
This parameter is for use only by Siemens service personnel.

7.27.3

P837 Auto false echo suppression

Note

•

P837 and P838 should be used together to adjust the TVT (Time Varying Threshold)

curve.

•

Use this function only if there is a minimum distance of 2 meters (6.5 feet) from the

reference point to the material.

•

Set P837 and P838 during start up, if possible.

•

If the vessel contains an agitator, the agitator should be running.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 66 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: