manualshive.com logo in svg

Shinko PCA1, Инструкция по эксплуатации


Поделиться
Скачать
background image

- 4 -

2. Wiring Precautions

Caution

• Do not leave wire remnants in the instrument, as they could cause a fire or malfunction.
• Use the solderless terminal with an insulation sleeve in which the M3 screw fits when wiring the

instrument.

• The terminal block of this instrument is designed to be wired from the left side. The lead wire must be

inserted from the left side of the terminal, and fastened with the terminal screw.

• Tighten the terminal screw using the specified torque. If excessive force is applied to the screw when

tightening, the terminal screw or case may be damaged.

• Do not pull or bend the lead wire on the terminal side when wiring or after wiring, as it could cause

malfunction.

• This instrument does not have a built-in power switch, circuit breaker and fuse. It is necessary to install

a power switch, circuit breaker and fuse near the controller.
(Recommended fuse: Time-lag fuse, rated voltage 250 V AC, rated current 2 A)

• For the grounding wire, use a thick wire (1.25 - 2.0 mm

2

).

• For a 24 V AC/DC power source, do not confuse polarity when using direct current (DC).
• Do not apply a commercial power source to the sensor which is connected to the input terminal nor

allow the power source to come into contact with the sensor.

• Use a thermocouple and compensating lead wire according to the sensor input specifications of this

controller.

• Use the 3-wire RTD according to the sensor input specifications of this controller.
• For DC voltage input, (+) side input terminal number of 0 to 5 V DC, 1 to 5 V DC, 0 to 10 V DC differs

from that of 0 to 10 mV DC, -10 to 10 mV DC, 0 to 50 mV DC, 0 to 100 mV DC, 0 to 1 V DC.

Terminal Number

DC Voltage Input

⑯

and

⑲

0 to 5 V DC, 1 to 5 V DC, 0 to 10 V DC

⑱

and

⑲

0 to 10 mV DC, -10 to 10 mV DC, 0 to 50 mV DC,
0 to 100 mV DC, 0 to 1 V DC

• When using a relay contact output type, externally use a relay according to the capacity of the load to

protect the built-in relay contact.

• When wiring, keep input wires (thermocouple, RTD, etc.) away from AC power sources or load wires.

3. Operation and Maintenance Precautions

Caution

• It is recommended that AT be performed on the trial run.

• When connecting USB communication cable (CMB-001) to the console connector, connect the cable

after power is turned OFF.

•

Never

turn the power ON or OFF, while USB communication cable (CMB-001) is connected to the

console connector.

• Do not touch live terminals. This may cause electrical shock or problems in operation.
• Turn the power supply to the instrument OFF before retightening the terminal or cleaning.

Working on or touching the terminal with the power switched ON may result in severe injury or death
due to electrical shock.

• Use a soft, dry cloth when cleaning the instrument.

(Alcohol based substances may tarnish or deface the unit.)

• As the display section is vulnerable, be careful not to put pressure on, scratch or strike it with a hard

object.

Содержание PCA1





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCA1

Abicor Binzel EWR Quick Install Instructions preview
EWR
Бренд: Abicor Binzel Страницы: 8
H3C S9500E Series Card Manual preview
S9500E Series
Бренд: H3C Страницы: 5
H3C WX1800H series Command Reference Manual preview
WX1800H series
Бренд: H3C Страницы: 27
H3C WX3500H series Installations preview
WX3500H series
Бренд: H3C Страницы: 4
H3C WX5540H Installation Manual preview
WX5540H
Бренд: H3C Страницы: 54
H3C LSWM1WCM10 Manual preview
LSWM1WCM10
Бренд: H3C Страницы: 10
H3C LSQM1WCMB0 Quick Start Manual preview
LSQM1WCMB0
Бренд: H3C Страницы: 10
Jandy AquaLink RS Troubleshooting Manual preview
AquaLink RS
Бренд: Jandy Страницы: 28
Jands 4PAK Operating Manual preview
4PAK
Бренд: Jands Страницы: 6
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Бренд: X-POWER Страницы: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44
VAT 670 Series Installation, Operating, & Maintenance Instructions preview
670 Series
Бренд: VAT Страницы: 39
Samson 3730-6 Mounting And Operating Instructions preview
3730-6
Бренд: Samson Страницы: 124

Бренды по названию

Популярные бренды

Загрузить еще бренды