Shinko PCA1 Скачать руководство пользователя | Manualshive

Страница: 173 / 180

background image

- 173 -

13. Making Program Pattern Table and Data Table

Before setting program, make a program pattern table and data table.

13.1 Making Program Pattern Table

Please make a copy of the program pattern table (p.177), and follow the procedure below.
(1) Write a block number (Step SV, Step time, PID, Time signal 1 to 8, Wait, Alarm, Output) for

each step from Step 0 in numerical order.

(Even if the same block number is used, write for every step.)

(2) Draw a line graph of step SV.

Explanation of Program Pattern Table

Program pattern table consists of Y axis which represents the step SV (°C, °F), and X axis which
represents the step time (Hours:Minutes, Minutes:Seconds).
Step SV is considered to be the SV at the end of the step.
Step time is considered to be the step process time.

• The relation between the step SV and Step time can be explained as follows.

Step 0: The control is performed so that the temperature reaches from 0 to 500°C for 30 minutes.

Depending on the selection in [Program control start type], control is performed as follows.
• When SV start is selected: Performs control from the step SV set in [Step SV when

program control starts] so that the temperature reaches 500°C.

• When PV start or PVR start is selected: Step SV and time are advanced to PV, and

control starts so that the temperature reaches 500°C.

Step 1: The control is performed so that SV is maintained at 500°C for 1 hour.
Step 2: The control is performed so that SV rises from 500°C to 1000°C for 40 minutes.
Step 3: The control is performed so that SV is maintained at 1000°C for 1 hour.
Step 4: The control is performed so that SV drops from 1000°C to 0°C for 2 hours.

• PID block includes: OUT1 proportional band, Integral time, Derivative time, ARW, OUT2 proportional

band
10 types of PID block (0 – 9) can be set.

• Time signal 1 to 8 (TS1 – TS8) includes: Time signal output OFF time and Time signal output ON

time.
16 types of Time signal block (0 – 15) can be set for Time signal 1 to 8 (TS1 – TS8) respectively.
For Time signal 1 to 5 (TS1 – TS5), the Time signal output can be used only when Time signal output
is selected in [Time signal output/Status output].

• Wait block includes Wait values.

10 types of Wait block (0 – 9) can be set.

• Alarm block includes: EV1 alarm value, EV2 alarm value, EV3 alarm value, EV4 alarm value

10 types of Alarm block (0 – 9) can be set.

• Output block includes: OUT1 high limit, OUT1 low limit, OUT2 high limit, OUT2 low limit, OUT1

rate-of-change.

10 types of Output block (0 – 9) can be set.

«
...
171
172
173
174
175
...
»

Содержание PCA1





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCA1

Бренд: FAAC Страницы: 14

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Canarm Страницы: 3

Бренд: GCE Страницы: 24

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Warren rupp Страницы: 18

Бренд: Yamaha Страницы: 100

Бренд: iluminize Страницы: 2

Бренд: Absima Страницы: 5

Бренд: SOMFY Страницы: 112

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Penn Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды