manualshive.com logo in svg

Shindaiwa DGK20FS, Руководство владельца и оператора

Поделиться
Скачать
Shindaiwa DGK20FS Скачать руководство пользователя страница 49

46 

 
 

Problem 

Suspected cause 

Action 

Engine starts but 

stalls immediately 

1. Fuel filter is clogged 
2. Water is interfused in fuel line 

 
3. Air is interfused in fuel line 
4.Mistake of connecting with external tank 
5. Air filter element is clogged 
6. Lubricant oil level is insufficient 
7.Emergency operation/Fault detection   

1. Clean/Replace fuel filter 
2. Drain water in water separator, fuel 

filter or fuel tank 

3. Extract the air 
4.Check fuel piping 
5. Check/Replace air filter element 
6. Add lubricant oil 
7.Ask our distributor to repair   

Engine oil pressure 

is low 

1. Lubricant oil is insufficient 
2. Oil filter is clogged 

 
3. Oil Pressure switch is defective 
4. Wrong oil is used 

1. Add lubricant oil 
2. Replace oil filter ask our distributor to 

repair

 

3. Contact our distributor to repair 
4. Change to proper kind and viscosity 

oil 

Overheated 

1. Engine thermostat is defective 
2. Water temp sensor is defective 
3. Water temp meter is defective 
4. Fan belt tension is loosen or 

insufficient. 

5. Coolant level is insufficient 
6. Radiator core is clogged 

1.Contact our distributor to repair 
2. Contact our distributor to repair 
3. Contact our distributor to repair 
4. Check/Adjust fan belt 
5. Check/Add coolant 
6. Clean radiator core 

Black smoke 
comes out from Muffler 

1. Air filter element is clogged 
2. Fuel injection nozzle is defective 
3. Improper fuel is used 

1. Check/Change air filter element 
2. Contact distributor or dealer for repair 
3. Change to clean fuel 

White smoke 
comes out from 
Muffler 

1. Too much or too little oil to cylinder 
2. Water is interfused in fuel line 
3. Fuel injection nozzle is defective 
4. Coolant temperature is too low 
5. Engine thermostat is defective 

1. Contact distributor or dealer for repair 
2. Drain water in fuel filter or fuel tank 
3. Contact distributor or dealer for repair 
4. Warm-up driving is needed 
5. Contact distributor or dealer for repair 

Voltage value does not 

change 

1. Controller is defective 
2. AVR is defective 
3. Disconnected circuit, loose terminal 

or departed 

4. Initial exciter is defective 
5. Alternator is defective 

1. Contact distributor or dealer for repair 
2. Contact distributor or dealer for repair 
3. Contact distributor or dealer for repair 

 
4. Contact distributor or dealer for repair 
5. Contact distributor or dealer for repair 

The voltage does not rise to 

the rated voltage 

1. Controller is defective 
2. AVR is defective 
3. Voltage regulator dial is defective 
4. Frequency is low 

1. Contact distributor or dealer for repair 
2. Contact distributor or dealer for repair 
3. Contact distributor or dealer for repair 
4. Contact distributor or dealer for repair 

The voltage value exceed the 

rated voltage 

1. Controller is defective 
2. AVR is defective 
3. Improper load cable connection 

1. Contact distributor or dealer for repair 
2. Contact distributor or dealer for repair 
3. Correctly set the connection location 

to the receptacle 

Cannot turn the breaker to 

ON 

1. The Main breaker positions were let 

in between ON and OFF 

2. Short circuit on the load 

1. Once turning the lever to OFF, turn it 

to ON 

2. Check the load circuit 

Содержание DGK20FS





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды