SEW MDR60A Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 148

background image

Operating Instructions – MOVIDRIVE® MDR60A/61B

107

12

Electrical connection

Installation (MDR60A1320-503-00)

12.3 Electrical connection

You will have access to the MOVIDRIVE

®

MDR60A1320-503-00 wiring space after re-

moval of the lateral knurled screw and housing cover. The incoming cables are guided
through the metal cable glands installed in the flange.

12.3.1 Power connection

Fusing:

• Consider the voltage drop in case of load when selecting the cable cross section.

• Protection of cables and regenerative power supply units on AC side (L1, L2, L3):

– Commercial semiconductor fuses

– Fuses and fuse holders/disconnector switches in UL-compliant systems must

have UL approval.

– Rated voltage of fuses must be configured according to the supply voltage on site.

• Protection of regenerative power supply units on the DC side (+UG, –UG):

– Fuses are installed in unit.

Connection:

• Make all connections as short and as low in inductance as possible.

• Use shielded cables to meet EMC directives (according to existing standards such

as VDE 0160 and EN 61800-5-1).

• Connect the supply cables to terminals L1, L2 and L3 of the regenerative power sup-

ply unit. Connection always has to be three phase.

• A certain phase sequence has to be observed for the power supply connections of

the power section (clockwise phase sequence). The unit comes equipped with a
phase monitoring option. If the phase monitoring detects an incorrect phase se-
quence, the unit will indicate the following error message with its LEDs "Incorrect ro-
tating field" or "Phase fault" (

→

chapter "Operation and Service" (page 121)). 2 sup-

ply system phases of the power supply connection will have to be replaced.

• Connect the cables for the DC link of drive controller and regenerative power supply

unit to terUG / -UG. Ensure correct polarity when making the connection!

• Observe the specified torques and use a 2. wrench to absorb the torque.

• Connect the equipment grounding conductor of the supply cable to the earthing

screw at the bottom of the unit.

NOTICE

Make sure not to damage or tear off the cables leading to the display board when
removing the cover!

NOTICE

Reversal or incorrect connection of + (plus) or – (minus) poles can destroy the
drive controller and the regenerative power supply unit!

«
...
105
106
107
108
109
...
»

Содержание MDR60A





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MDR60A

Бренд: Hakko Electronics Страницы: 4

Бренд: Oasser Страницы: 34

Бренд: U-Line Страницы: 6

Бренд: Ironton Страницы: 21

Бренд: Ancor Страницы: 12

Бренд: Wel-Bilt Страницы: 7

Бренд: Parkside Страницы: 27

Бренд: YATO Страницы: 64

Бренд: MAIMAN ELECTRONICS Страницы: 24

Бренд: Radio Shack Страницы: 13

Бренд: Somogyi Страницы: 31

Бренд: OLI Страницы: 2

Accelerator 2000

Бренд: Rapid Страницы: 76

Бренд: Kamasa-TOOLS Страницы: 12

Бренд: OfiTE Страницы: 20

Бренд: Rapid Страницы: 87

Бренд: Central Machinery Страницы: 15

Бренд: Paxton Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды