SEW MDR60A Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 148

background image

Operating Instructions – MOVIDRIVE® MDR60A/61B

117

14

Important notes on configuration

Configuration (MDR60A1320-503-00)

14

Configuration (MDR60A1320-503-00)

The coding of jumpers (jumpers J3, J5, J6, J7, J8) on the control card offers different
control options and different internal functions for certain error messages.

The different terms that result from certain coding options are explained below.

14.1 Important notes on configuration

14.1.1 Autostart

"Autostart" means that the unit starts up automatically with a delay of 1 s once the supply
voltage has been applied. The "Autostart" function is coded with jumper J1 on the control
card and may not be altered.

14.1.2 Switch-off – switch-on

"Switch-off" means that control of the power semiconductors and regeneration is inter-
rupted and braking operation of the drive controllers is no longer possible.

"Switch-on" means control of the power semiconductors is being activated.

14.1.3 Save

The unit comes equipped with an error memory that can be assigned certain errors.
Saved error messages must be confirmed via reset or interruption of the supply voltage
of the control component power supply. "Save" always results in a simultaneous "switch-
off" and dropping out of the centralized alarm relay.

14.1.4 Confirmation

Once an error has been remedied, the error memory will have to be confirmed with the
ON confirmation key or disconnection of the three-phase power supply.

NOTICE

• Confirmation of an excessive DC link voltage, i.e. during braking operation, is not

permitted and may destroy the unit!

«
...
115
116
117
118
119
...
»

Содержание MDR60A





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MDR60A

Бренд: Altronix Страницы: 2

Бренд: Dake Страницы: 24

Бренд: Davey Water Products Страницы: 4

Бренд: Kärcher Страницы: 148

Бренд: Keithley Страницы: 10

Бренд: Makita Страницы: 40

Бренд: Cocraft Страницы: 56

Bristle Blaster Pneumatic

Бренд: Monti Страницы: 268

Бренд: Agilent Technologies Страницы: 142

ProJet Cart Station

Бренд: 3D Systems Страницы: 21

Бренд: Larzep Страницы: 8

Бренд: Hilti Страницы: 14

Бренд: Hama Страницы: 2

Бренд: National Instruments Страницы: 47

Бренд: Eastwood Страницы: 3

Бренд: FEAS Страницы: 6

Бренд: Wacker Neuson Страницы: 44

Бренд: Cleco Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды