Servomex SERVOTOUGH Oxy Скачать руководство пользователя страница 44

Страница: 44 / 145

01910001B_8

•

Ensure that the cables that you connect to the analyser

are routed so that they do not

present a trip hazard.

•

When you carry out insula�on tes�ng, disconnect all cables from the

analyser

5.3.2

Configure the cable entry

holes

If the analyser

is installed in a hazardous area, all cable

glands, adaptors and blanking

plugs must be suitably approved.

•

ATEX approved

analysers must be ﬁted with IP66 ATEX Ex d IIC approved

components.

•

IECEx approved

analysers must be ﬁted with IP66 IECEx Ex d IIC

approved

components.

•

CSA North American Approved analysers must be ﬁted with CSA/UL, cULus
or cCSAus 4X, Class I, Groups A, B, C, D approved components.

The

analyser

has two 3/4 inch and two 1/2 inch NPT cable entry holes. As supplied, three of these holes

are ﬁted with blanking plugs (rated to IP66 / NEMA 4X).

Conﬁgure

the

analyser

so that the entry holes that you use for the electrical supply and signal

connec�on cables have suitable cable

glands (and/or adaptors) ﬁted, and so that any unused entry hole

has a blanking plug ﬁted.

All cable

glands/adaptors and plugs used must provide ingress protec�on to IP66, NEMA 4X or beter.

Note:

It is recommended that the 1/2 inch NPT cable entry hole on the far right hand side of

the enclosure is used for the power supply cable.

5.3.3

Interface signal

connections

All of the analyser

interface signal outputs are considered to be incendive and

therefore must only be connected to safe area equipment.

To comply with EMC requirements, you must use a screened 4 to 20 mA cable to
connect to the mA output. It is recommended that screens

are terminated at the

cable gland.

Connect the wires in your cables to the appropriate terminals as described below and refer to Sec�on

2.3

for detailed ra�ngs and cable sizes.

Pass your signal cable(s) through one or two

of the cable

glands ﬁted to the base of the

power/interface compartment.

Refer to Figure 4. Connect the mA output wires in your cables to the corresponding

terminal pins of the mA output, as follows:

Содержание SERVOTOUGH Oxy


















































































































































Результаты поиска

Содержание SERVOTOUGH Oxy

Отзывы:

Бренды по названию

Популярные бренды

Servomex SERVOTOUGH Oxy, Руководство оператора

Результаты поиска

Содержание SERVOTOUGH Oxy

Отзывы:

Бренды по названию

Популярные бренды