Server Technology Switched Rack PDU Скачать руководство пользователя страница 90

Страница: 90 / 157



Operations Switched PDU

Installation and Operations Manual

Setting the SNTP server address:

The Set SNTP command is used to set the primary and secondary SNTP server addresses.

To set the SNTP server address:

At the Switched CDU: prompt, type

set sntp

, followed by

primary

secondary

, and the SNTP server IP address or

hostname. Press

Enter

NOTES:



The primary/secondary IP addresses contact the SNTP server; these addresses are populated with the external NTP pool time zones

“2.servertech.pool.ntp.org” and “1.servertech.pool.ntp.org” as default for new PDUs that have not yet been time set.



Both IPv4 and IPv6 formats are accepted for primary/secondary IP address or hostname.

Examples

The following command sets the primary SNTP server address to 204.152.184.72:

Switched CDU: set sntp primary 204.152.184.72<Enter>

The following command sets the secondary SNTP server address to cuckoo.nevada.edu:

Switched CDU: set sntp secondary cuckoo.nevada.edu<Enter>

Setting the local GMT offset (hours/minutes):

The Set SNTP GMToffset command sets the offset from GMT for the date/time returned by SNTP.

The GMT offset supports all standard international time zones from -12:59 to +14.59. The GMT offset can be set in
minutes to accommodate partial-hour time zones.

NOTE:

The PDU does not support automatic adjustment for Daylight Saving Time (DST).

To set the local GMT offset:

At the Switched CDU: prompt, type

set sntp gmtoffset

, followed by the offset value, and press

Enter

Examples

The following command sets the local GMT offset to -12:

Switched CDU: set sntp gmtoffset -12<Enter>

Displaying SNTP configuration information:

The Show SNTP command displays all SNTP configuration information.

To display SNTP configuration information

At the Switched CDU: prompt, type

show sntp

and press

Enter

Example

The following command displays the SNTP configuration information:

Switched CDU: show sntp <Enter>
Date/Time:

2013-04-13 15:21:18

Primary Host: 204.152.184.72
Secondary Host: 1.servertech.pool.ntp.org
Local GMT Offset: -8
Use DST: Enabled
Start Date: 1

Wednesday in April

Start Time: 04:18:06
End Date: 1

Sunday in November

End Time: 02:00:00

Содержание Switched Rack PDU






























































































































































Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Бренды по названию

Популярные бренды

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Бренды по названию

Популярные бренды