Server Technology Switched Rack PDU страница 133 Скачать руководство пользователя

Страница: 133 / 157

Switched PDU
Installation and Operations Manual

Advanced Operations



133

Setting the RADIUS server address:

The Set RADIUS Server command sets the IP address or hostname of the primary or secondary server used for
RADIUS authentication requests.

NOTE:

Both IPv4 and IPv6 formats are accepted for primary/secondary IP address or hostname.

To set the RADIUS server address:

At the Switched CDU: prompt, type

set radius

, followed by

primary

secondary

, followed by

server

, and the

RADIUS server’s IP address or hostname (maximum 63 characters). Press

Enter

Examples

The following command sets the primary RADIUS server address to 98.76.54.32:

Switched CDU: set radius primary server 98.76.54.32<Enter>

The following command sets the secondary RADIUS server address to radius.servertech.com:

Switched CDU: set radius secondary server radius.servertech.com<Enter>

Setting the RADIUS secret:

The Set RADIUS Secret command sets the shared secret for the server used for RADIUS authentication requests.

To set the shared secret:

At the Switched CDU: prompt, type

set radius

, followed by

primary

secondary

, and followed by

secret

. Press

Enter

Enter the shared secret and press

Enter

. For security, shared secret characters are not displayed.

The secret that was set for the primary server will not be cleared when setting the secret for the secondary server, and
vice versa.

Changing the RADIUS port number:

The Set RADIUS Port command sets the server port number for RADIUS authentication requests.

To change the port number:

At the Switched CDU: prompt, type

set radius

, followed by

primary

secondary

, followed by

port

, and the port

number (1-65535). Press

Enter

The default is 1812.

Example

The following command sets the secondary RADIUS server port number to 1855:

Switched CDU: set radius secondary port 1855<Enter>

Setting the RADIUS timeout value:

The Set RADIUS Timeout command sets the time interval to wait for a reply from the RADIUS server before
resending the authentication request.

To set the timeout value:

At the Switched CDU: prompt, type

set radius

, followed by

primary

secondary

, followed by

timeout

, and the

time interval in seconds (1-30). Press

Enter

Examples

The following command sets the primary RADIUS server timeout value to 15 seconds:

Switched CDU: set radius primary timeout 15<Enter>

The following command sets the secondary RADIUS server timeout value to 5 seconds:

Switched CDU: set radius secondary timeout 5<Enter>

Содержание Switched Rack PDU






























































































































































Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Похожие инструкции для Switched Rack PDU

Бренды по названию

Популярные бренды

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Похожие инструкции для Switched Rack PDU

Бренды по названию

Популярные бренды