Server Technology Switched Rack PDU Скачать руководство пользователя страница 117

Страница: 117 / 157

Switched PDU
Installation and Operations Manual

Advanced Operations



117

Enabling and setting up LDAP support

There are a few configuration requirements for properly enabling and setting up LDAP support. Below is an
overview of the minimum requirements.

Directory Services server configuration requirements:

Define at least one LDAP group.

Assign users to that LDAP group.

Configuration requirements:

Enable LDAP support.

Define the IP address and domain component of at least one Directory Services server.

Set the LDAP bind request method being utilized by the Directory Services server.

Define the IP address of at least one DNS server.

Test DNS server configuration using the PDU Ping support.

Define at least one LDAP group and assign access rights for that group.

NOTE:

LDAP group names on the Directory Service Server and the PDU must match.

Enabling and disabling LDAP support:

The Set LDAP command is used to enable or disable LDAP support.

To enable or disable LDAP support:

At the Switched CDU: prompt, type

set ldap

, followed by

enabled

disabled

and press

Enter

Setting the LDAP host address:

The Set LDAP Host command sets the TCP/IP address of the Directory Services server.

NOTE:

Both IPv4 and IPv6 formats are accepted for hostname.

To set the LDAP host address:

At the Switched CDU: prompt, type

set ldap

, followed by

host1

host2

and the Directory Services server’s IP

address or hostname. Press

Enter

Examples

The following command sets the primary Directory Services server IP address to 98.76.54.32:

Switched CDU: set ldap host1 98.76.54.32<Enter>

The following command sets the secondary Directory Services server hostname to ldap.servertech.com:

Switched CDU: set ldap host2 ldap.servertech.com<Enter>

Changing the LDAP server port:

The Set LDAP Port command sets the port to which the PDU sends LDAP requests to on the previously defined
LDAP server. The default port is 389.

To change the LDAP server port:

At the Switched CDU: prompt, type

set ldap port

, followed by the port number and press

Enter

Example

The following command sets the LDAP server port number to 8888:

Switched CDU: set ldap port 8888<Enter>

Содержание Switched Rack PDU






























































































































































Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Бренды по названию

Популярные бренды

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Switched Rack PDU

Отзывы:

Бренды по названию

Популярные бренды