manualshive.com logo in svg

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Поделиться
Скачать
Server Technology Switched Rack PDU Скачать руководство пользователя страница 9

Switched PDU 
Installation and Operations Manual 

Introduction  

 

9

 

 

Viewing Network Status 

 

You can obtain the IPv6 network status through the firmware Web Interface or Command Line Interface (CLI). For 
the CLI, use the 

show network

 command as follows: 

 

Switched CDU: show network 

Network Settings 

State: DHCP IPv6/IPv4  Network: Dual IPv6/IPv4    
Link: Up  

 

Negotiation: Auto 

Speed: 100 Mbps  

Duplex: Full 

 

 

AutoCfg IPv6: FE80::20A:9CFF:FE52:4104/64 
IPv6 Address: FD01::1:B51A:E03C/64 
IPv4 Address: 10.1.6.230 Subnet Mask: 255.255.0.0 
IPv4 Gateway: 10.1.1.1 
DNS1: FD01::A01:585 
DNS2: 10.1.5.133 

 
Static IPv4/IPv6 Settings 

IPv6 Address: FD01::A01:353/64 
IPv6 Gateway: :: 
IPv4 Address: 10.1.2.253 Subnet Mask: 255.255.0.0 
IPv4 Gateway: 10.1.1.1 
DNS1: 10.1.5.133 
DNS2: 10.1.5.134 
 

DHCP Settings 

DHCP: Enabled 
FQDN: Enabled [sentry3-524104] 
Boot Delay: Enabled 
Static Fallback: Enabled 
 

Network Services 

Telnet:       Enabled            Port: 23 
SSH:          Enabled            Port: 22           Auth: Password, Kb-Int 
HTTP:         Enabled            Port: 80 
SSL:          Enabled            Port: 443          Installed Cert: User Encrypted 
   Access:    Optional                              Stored Files: Cert & Key 
   User Cert: Enabled                               User Passphrase: <set>  
SNMPv1/2:     Enabled            Port: 161          TrapPort: 162 
SNMPv3:       Disabled           Port: 161          TrapPort: 162 
FTP Server:   Enabled            Port: 21 
SPM Access:   Enabled 

Command successful 

 

NOTE

: The fields IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway, DNS1, and DNS2 are equivalent to existing IPv4 settings except that 

current network settings and static settings are displayed separately. This allows you to view both static configuration settings and active 
network settings that can be obtained using DHCP. The DNS addresses may be in IPv4 or IPv6 (based on RFC4291) format at this time. 

 

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды