Server Technology Switched Rack PDU страница 73 Скачать руководство пользователя | Manualshive

Страница: 73 / 157

background image

Switched PDU
Installation and Operations Manual

Operations



73

Setting the serial port timeout value:

The Set Port Timeout command sets the serial port inactivity timeout period. The timeout period defines the
maximum period of inactivity before automatically closing the Pass-Thru session.

The valid range for the timeout is 0 to 60 (in minutes). The default timeout is 5 minutes. The command can be used to
set individual ports by ID or name.

NOTES

:



Setting the timeout value to “0” disables the timer.



Only a numeric value is accepted.

To set the serial port timeout value for an individual port:

At the Switched CDU: prompt,

type set port timeout

, followed by the port ID or name, followed by a timeout value

from 0 to 60 (in minutes), and press

Enter

.

Configuring the Blue

tooth™ options:

If the PDU has been equipped for the mobile monitoring solution using Bluetooth

®

technology, several Bluetooth

parameters will be available for editing on the Serial Ports configuration page.

To set the Bluetooth™ module name:

The Bluetooth™ module name displays in the list of discovered modules on the Android device. The default is “ST
Eye”, and the module name cannot be blank.

At the Switched CDU: prompt, type

set bluetooth name

, followed by 1-31 characters of a descriptive name for the

module, and press

Enter

.

To set the Bluetooth™ discoverability:

Three discoverability settings determine the current status of the pushbutton on the Bluetooth module:



Always - The Bluetooth module is discoverable, even without pressing the pushbutton.



Limited (Default) - The pushbutton on the Bluetooth module must be pressed to make the module
discoverable for 60-seconds.



Never - The Bluetooth module is never in discoverable mode.

At the Switched CDU: prompt, type

set bluetooth discover

, followed by

always

,

limited

, or

never

, and press

Enter

.

To set the Bluetooth™ pin code:

The pin code is available for legacy Bluetooth modules that require a pin to pair the module. Although not used in
current Bluetooth modules, the pin code is supported if needed. The default is 9611.

At the Switched CDU: prompt, type

set bluetooth pincode

, followed by 4-digits from 0000 to 9999, and press

Enter

.

To set the Bluetooth™ transmission power:

This setting is the designated transmission power (dbm) for the Bluetooth module. Note that lowering the
transmission power reduces the effective range of the module. Default is 0

At the Switched CDU: prompt, type

set bluetooth transpwr

, followed by a value from -6 to 4 (dbm), and press

Enter

.

«
...
71
72
73
74
75
...
»

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switched Rack PDU

Бренд: Panamax Страницы: 2

Бренд: NF Страницы: 304

Бренд: PCB Piezotronics Страницы: 13

System X High Voltage DC PDU

Бренд: IBM Страницы: 54

Бренд: Maxxima Страницы: 2

Бренд: Unika Страницы: 4

Бренд: Lazer Safe Страницы: 55

Relion 630 Series

Бренд: ABB Страницы: 108

SIVACON 8PS BD2-S120-B Series

Бренд: Siemens Страницы: 11

Бренд: Siemens Страницы: 106

Бренд: Sterling Power Products Страницы: 2

Бренд: Novatek Страницы: 42

Бренд: EXAGATE Страницы: 3

PWG IP PDU Series

Бренд: EXAGATE Страницы: 4

Бренд: Amulex Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды