manualshive.com logo in svg

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации


Поделиться
Скачать
background image

78

 

 Operations                                                                                Switched PDU  

                                                                                                          Installation and Operations Manual 

Configuring the LED display orientation: 

The Set Option Display command configures the LED display orientation. 

To configure the LED display orientation: 

At the Switched CDU: prompt, type 

set option display

, followed by 

normal, inverted

, or 

auto

, and press 

Enter

. 

Example 

 

The following sets the LED display orientation to Inverted: 

Switched CDU: set option display inverted<Enter> 

 

NOTES: 

 

  Only specific PDU models are equipped with an accelerometer chip that senses device orientation. If equipped, your PDU automatically 

     aligns the LED display orientation depending on its current direction, and “Auto” will display in the Show Options command by default.  
     In addition, the actual mounting of the unit, such as such as “<Normal> or <Inverted>”, appears to the right of the "Auto" option when 
     you issue the Show Options command. However, even if your model does have the sensor for device orientation, you can still 
     issue the Set Option Display command with either the Normal or Inverted option to override the capability of the hardware.  

  If your model does not have the accelerometer chip, you will need to configure the LED display orientation by entering the Normal 

    or Inverted option. 

 

Enabling or disabling strong passwords: 

The Set Option Strong Password command is used to enable or disable the requirements for strong passwords.  When 
enabled, all new passwords must be a minimum of 8 characters in length with at least one uppercase letter, one 
lowercase letter, one number and one special character. 

To enable or disable strong passwords: 

At the Switched CDU: prompt, type 

set option strong password

, followed by 

enabled

 or 

disabled

 and press 

Enter

. 

Enabling or disabling the external configuration reset button: 

The Set Option Button command enables or disables the external configuration reset button.  This feature can enhance 
system security by protecting the PDU configurations from being reset locally. 

NOTE:

  If this feature has been enabled and the administrative account username/password has been lost, then the PDU must be returned to 

the factory for non-warranty reset of the configuration. 

To enable or disable the configuration reset button: 

At the Switched CDU: prompt, type 

set option button

, followed by 

enabled 

or 

disabled

 and press 

Enter

. 

Enabling or disabling the ‘more’ prompt: 

The Set Option More command enables or disables the ‘more’ prompt for display of data larger than the terminal 
window.   

To enable or disable ‘more’: 

At the Switched CDU: prompt, type 

set option more

, followed by 

enabled 

or 

disabled

 and press 

Enter

. 

Setting the outlet sequence order: 

The PDU allows the configuration of power-on sequence for outlets.  

The Normal option powers-on outlets in ascending numeric order by outlet number, for example, from outlet 1-8. The 
Reversed option powers on outlets in descending order by outlet number; for example, from outlet 8-1. 

The Reversed option is useful when the PDU is mounted with inverted orientation and the last outlet (in this example, 
outlet 8) is in the first position.   

At the Switched CDU: prompt, type 

set option outletsequence

, followed by 

normal

 or 

reversed

, and press 

Enter

. 

Setting the temperature scale: 

The Set Option TempScale command sets the temperature scale reported by the PDU.   

To set the temperature scale: 

At the Switched CDU: prompt, type 

set option tempscale

, followed by 

celsius 

or 

fahrenheit

 and press 

Enter

. 

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switched Rack PDU

S&C VacuFuse Installation And Operation Manual preview
VacuFuse
Бренд: S&C Страницы: 24
Shunyata Research HYDRA TRITON v2 User Manual preview
HYDRA TRITON v2
Бренд: Shunyata Research Страницы: 8
EuroLite SBM-63B User Manual preview
SBM-63B
Бренд: EuroLite Страницы: 16
Daikin VRV Series Technical Data Manual preview
VRV Series
Бренд: Daikin Страницы: 38
Daxten STARLINE Datasheet preview
STARLINE
Бренд: Daxten Страницы: 6
JR ProPo PDX16 Operation Manual preview
PDX16
Бренд: JR ProPo Страницы: 3
Datavideo PD-6 Quick Start Manual preview
PD-6
Бренд: Datavideo Страницы: 8
AudioQuest PowerQuest 2 User Manual preview
PowerQuest 2
Бренд: AudioQuest Страницы: 2
Black Lion Audio PG-X Type C Owner'S Manual preview
PG-X Type C
Бренд: Black Lion Audio Страницы: 2
Black Lion Audio PG-1 mkII Quick Start Manual preview
PG-1 mkII
Бренд: Black Lion Audio Страницы: 2
Tripp Lite AG-019E Owner'S Manual preview
AG-019E
Бренд: Tripp Lite Страницы: 20
Tripp Lite AG-00C2 Owner'S Manual preview
AG-00C2
Бренд: Tripp Lite Страницы: 68
Tripp Lite PDU1420T Specification Sheet preview
PDU1420T
Бренд: Tripp Lite Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды