manualshive.com logo in svg

Server Technology Switched Rack PDU, Инструкция по установке и эксплуатации

Поделиться
Скачать
Server Technology Switched Rack PDU Скачать руководство пользователя страница 139

Switched PDU 
Installation and Operations Manual 

                                                            Advanced Operations  

 

139

 

Changing the SMTP server port: 

With SMTP support enabled, the PDU sends SMTP requests to the default SMTP port number 25. You can change this port 
number using the Set Email SMTP Port command. 

To change the TACACS port: 

At the Switched CDU: prompt, type 

set email smtp port

, followed by the port number and press 

Enter

. 

Example 

The following changes the SMTP port number to 5555: 

Switched CDU: set email smtp port 5555<Enter> 

Setting the ‘From’ email address: 

The Set Email From command sets the “from” email address.  By default, this is set to ‘Sentry3_’ plus the last three 
octets of the unit’s MAC address.  Example: ‘Sentry3_510c90@’ 

To set the ‘From’ email address: 

At the Switched CDU: prompt, type 

set email from

, followed by the originating email address and press 

Enter

. 

Example 

 

 

The following command sets the ‘from’ email address to [email protected]: 

Switched CDU: set email from [email protected]<Enter> 

Setting the ‘Send To’ email address: 

The Set Email PrimaryTo and Set Email SecondaryTo commands set the recipient email addresses.   

To set the ‘Send To’ email address: 

At the Switched CDU: prompt, type 

set email

, followed by 

primaryto 

or 

secondaryto 

and the destination email 

address.  Press 

Enter

. 

If the primary ‘send to’ address fails, the system then attempts to send the email to the secondary ‘send to’ address. 

Examples 

 

 

The following command sets the primary ‘to’ email address to [email protected]: 

Switched CDU: set email primaryto [email protected]<Enter> 

The following command sets the secondary ‘to’ email address to [email protected]: 

Switched CDU: set email secondaryto [email protected]<Enter> 

Setting the Email SMTP authentication username: 

The Set Email SMTP Username command sets the username for SMTP authentication. 

At the Switched CDU: prompt, type 

set email smtp username

, followed by the SMTP username, and press 

Enter

. 

Spaces are not allowed. 

Setting the Email SMTP authentication password: 

The Set Email SMTP Password command sets the password for SMTP authentication with username. 

At the Switched CDU: prompt, type 

set email smtp password

, followed by the SMTP password, and press 

Enter

. 

Setting the Email SMTP Use Username : 

The Set Email SMTP Useusername command uses the SMTP username for SMTP authentication. 

At the Switched CDU: prompt, type 

set email smtp useusername

, followed by the username, and press 

Enter

. 

Setting the Email SMTP Use ‘From’ Address: 

The Set Email SMTP Usefromaddr command uses the SMPT ‘From’ address for SMTP authentication.   

At the Switched CDU: prompt, type 

set email smtp usefromaddr

, and press 

Enter

 

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды