SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 67

Страница: 67 / 83

7 Receiver Administration Operations

7.1 How

change

settings

the

AsteRx-U3

The IP settings of the AsteRx-U3 can be con

ﬁ

gured on the

Ethernet

window of the Web

Interface. By default, the AsteRx-U is con

ﬁ

gured to use DHCP to obtain an IP address but, a

static IP address can also be con

ﬁ

gured as shown in Figure 7-1.

In Static mode, the receiver will not attempt to request an address via DHCP but will use the
speci

ﬁ

ed IP address, netmask, gateway, domain name and DNS. DNS1 is the primary DNS,

and DNS2 is the backup DNS. In DHCP mode, the arguments IP, Netmask, Gateway, Domain,
DNS1, and DNS2 are ignored.

Figure 7-1:

Con

ﬁ

guring a static IP address

The new IP address should now appear in the

Ethernet Status

ﬁ

eld as shown in Figure 7-2.

Figure 7-2:

TCP/IP settings

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды