SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 83

background image

4 Rover operation

4.1 How to con

ﬁ

gure the AsteRx-U3 for RTK

The AsteRx-U3 can use correction data to calculate a cm-level RTK position. The AsteRx-U3
can get this correction data in several ways: using the built-in UHF radio, over GSM/GPRS or
Ethernet.

4.1.1 How to con

ﬁ

gure the AsteRx-U3 in RTK rover

mode using the UHF radio

When GSM/GPRS network coverage is either sparse or unreliable, RTK correction data can
be transmitted over UHF radio. The AsteRx-U3 has a built-in Satel radio modem that can be
used to both receive and transmit data.

Step 1: Enable RTK mode

RTK should be enabled as a positioning mode. This can be done in the

GNSS, Position

window by checking the

RTK

box in the

Position Mode

ﬁ

eld as shown in Figure 4-1. The

default setting is for all positioning modes to be enabled.

Figure 4-1:

Ensure that RTK positioning mode is enabled

34

«
...
32
33
34
35
36
...
»

Содержание AsteRx-U3




















































































Отзывы:

Нет отзывов

Похожие инструкции для AsteRx-U3

Бренд: Hallicrafters Страницы: 8

Бренд: Harman Kardon Страницы: 13

Бренд: Offshore Страницы: 14

Performance AV1

Бренд: JBL Страницы: 160

Бренд: Samsung Страницы: 94

Бренд: Yaesu Страницы: 80

EWFS Plug receiver PL

Бренд: WAREMA Страницы: 6

Бренд: Dual Страницы: 38

Бренд: Aiwa Страницы: 23

Бренд: Renkforce Страницы: 8

Penntek Preliminary TR-45L

Бренд: WA3RNC Страницы: 5

Бренд: JRC Страницы: 58

Digital Freeview Receiver

Бренд: Tevion Страницы: 2

Бренд: Dual Страницы: 1

MusicFly i-Select

Бренд: DNT Страницы: 48

EL-4KHDBT-RX-40-IRS

Бренд: Elan Страницы: 12

Бренд: Convex Страницы: 36

Бренд: Cobra Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды