SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 68

Страница: 68 / 83

7.2. HOW TO CONFIGURE DYNAMIC DNS

Note that the IP settings will keep their value after a power cycle and even after a reset to
factory default in order to avoid accidentally losing an Ethernet connection to the receiver.

7.2 How to con

ﬁ

gure Dynamic DNS

Dynamic DNS allows remote contact with the AsteRx-U3 using a hostname.

When devices are connected to the internet, they are assigned an IP address by an internet
service provider (ISP). If the IP address is

dynamic

then it may change over time resulting in a

loss of connection. Dynamic DNS (DynDNS or DDNS) is a service that addresses this problem
by linking a user-de

ﬁ

ned hostname for the device to whichever IP address is currently

assigned to it.

To make use of this feature on the AsteRx-U3, you should

ﬁ

rst create an account with a

Dynamic DNS provider (

dyndns.org

no-ip.org

) to register a hostname for your receiver.

In the example shown in Figure 7-3, the hostname

asterxu.mine.nu

has been registered with

dyndns.org. The

Bind

option, selected in this case, tells the Dynamic DNS provider only to

update IP addresses assigned over an Ethernet LAN connection.

Figure 7-3:

Con

ﬁ

guring Dynamic DNS

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды