SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 83

background image

1 Introduction

1.1 User Notices

1.1.1 CE Notice

AsteRx-U3 receivers carry the CE mark and are as such compliant with the
2014/53/EU - Radio Equipment Directive (RED), 2011/65/EU - Restriction
of Hazardous Substances (RoHS) Directive and 93/68/EC - CE-marking
Directive.

With regards to EMC, the AsteRx-U3 receiver is declared as class A, suitable
for residential or business environment. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.

1.1.2 ROHS/WEEE Notice

The

AsteRx-U3

receivers

are

compliant

with

the

latest

WEEE,

RoHS

and

REACH

directives.

For

more

information

see

www.septentrio.com/en/environmental-compliance.

1.1.3 Safety information

The power supply provided by Septentrio (if any) should not be replaced by
another. If you are using the receiver with your own power supply, it must
have a double isolated construction and must match the speciﬁcations of
the receiver.

Ultimate disposal of this product should be handled according to all
national laws and regulations.

5

«
...
3
4
5
6
7
...
»

Содержание AsteRx-U3




















































































Отзывы:

Нет отзывов

Похожие инструкции для AsteRx-U3

Бренд: Panasonic Страницы: 24

Бренд: Harman Страницы: 30

Performance AV1

Бренд: JBL Страницы: 160

Бренд: Raymer Страницы: 3

Бренд: MadgeTech Страницы: 4

wM-Bus 868 USB Key

Бренд: MADD Страницы: 4

Portable CD Player

Бренд: Jensen Страницы: 12

Бренд: Onkyo Страницы: 57

Бренд: Sencor Страницы: 17

Бренд: Boss Audio Systems Страницы: 15

Бренд: Kramer Страницы: 2

Бренд: Lafayette Страницы: 30

Бренд: Dish Network Страницы: 26

Бренд: Optimus Страницы: 40

Бренд: Xoro Страницы: 84

Бренд: Novus Страницы: 72

Бренд: V2 Страницы: 16

Бренд: C4Line Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды