SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 49

Страница: 49 / 83

4.3. HOW TO OUTPUT A PPS SIGNAL

4.3 How to output a PPS signal

The AsteRx-U3 can output a PPS (Pulse-per-Second) signal that can be used for example, to
synchronize a secondary device to UTC time.

Step 1: Connect the PPS cable

Connect the PPS_OUT cable to the rear-panel connector labelled ‘PPS GPO’ and indicated in
Figure 4-19.

Figure 4-19:

PPS connector on rear panel

Step 2: Con

ﬁ

gure the PPS settings

You can con

ﬁ

gure the PPS settings on the

PPS/Timing

window on the

GNSS

menu as shown

in Figure 4-20.

Figure 4-20:

The

GNSS, PPS/Timing

window

The

Interval

is the time interval between successive timing pulses and is selectable between

10ms and 10s. The default

Polarity

of the PPS signal is a low-to-high transition which can be

alternatively con

ﬁ

gured as high-to-low.

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды