SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 83

background image

3 Quick start

This section details how to power-up, connect to and communicate with the AsteRx-U3. The
AsteRx-U3 has an on-board web interface which the user can connect to in three ways:
Ethernet, USB or WiFi. The AsteRx-U3 is fully con

ﬁ

gurable using the web interface. Please

note that older versions of certain browsers may not display the web interface properly.

3.1 Powering the AsteRx-U3

Using a power cable, the receiver can be powered by applying 9 to 48 V via the power-in wire.
The power socket is indicated in Figure 3-1.

Figure 3-1:

Rear panel power socket

AsteRx-U3 can also use Power over Ethernet, 802.3af mode A (37-57 VDC) by using the ETH
socket.

Figure 3-2:

Rear panel ETH socket

The AsteRx-U3 does not have a power button and the unit will power up automatically when
power is applied. When the unit is powered initially, the front-panel LEDs will follow a boot
sequence pattern.

18

«
...
16
17
18
19
20
...
»

Содержание AsteRx-U3




















































































Отзывы:

Нет отзывов

Похожие инструкции для AsteRx-U3

Бренд: JCM Technologies Страницы: 3

Бренд: Radio Shack Страницы: 44

SAINT MALO RCM 127

Бренд: Blaupunkt Страницы: 23

Бренд: Exsys Страницы: 2

Бренд: Sena Страницы: 29

Бренд: Altronix Страницы: 8

Бренд: IMG STAGELINE Страницы: 24

Бренд: RCAVICTOR Страницы: 26

Бренд: Harman Kardon Страницы: 12

Бренд: Aiwa Страницы: 33

EXTA LIFE ROM-22

Бренд: Zamel Страницы: 5

Бренд: Hall Research Technologies Страницы: 12

Бренд: Salus Страницы: 2

Бренд: TEUCER Страницы: 4

Бренд: Xoro Страницы: 40

Бренд: HTRONIC Страницы: 24

Бренд: Telcoma Automations Страницы: 56

Бренд: Curtis Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды