SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 47

Страница: 47 / 83

4.2. HOW TO CONFIGURE THE ASTERX-U3 FOR ATTITUDE

Step 2: Con

ﬁ

gure attitude settings

The attitude settings of the AsteRx-U3 can be con

ﬁ

gured in the

GNSS, Attitude

window as

shown in Figure 4-16.

Figure 4-16:

GNSS Attitude window when two antennas are connected

GNSS Attitude ﬁeld

The recommended settings for a Heading setup are

MultiAntenna

mode with attitude

calculated using

Fixed

ambiguities as shown. These setting are con

ﬁ

gured by default.

Antenna Location and Antenna Oﬀset

The AsteRx-U3 assumes that the main and auxiliary antennas are placed along the
longitudinal axis of the vehicle with the auxiliary in front of the main antenna. If the antennas
cannot be placed in such a con

ﬁ

guration, the reported heading and pitch may be biased. The

default settings in the

Antenna Oﬀset

and

Antenna Location

ﬁ

elds shown in Figures 4-16

can be altered to compensate for these biases.

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды