SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 13

Страница: 13 / 83

2.3. ASTERX-U3 DESIGN

Figure 2-3:

SIM card slot on the AsteRx-U3

2.3.5 Mounting brackets

The AsteRx-U3 is supplied with mounting brackets for

ﬁ

xing the unit using 4 bolts. The size

of the

ﬁ

xing bolts can be M6 or smaller and the distance between the holes is shown in

Figure 2-4.

Important

: When selecting a mounting location for the receiver, please take into account

the following precautions:

•

When installed in vehicles, the unit should be properly secured to avoid injuries or
damaging the receiver or nearby equipment.

•

Select a mounting location that allows enough space to access the front and rear panel
of the AsteRx-U3.

•

Make sure the receiver and the cables will not be damaged, for example by moving
parts or sharp edges.

•

Make sure the conditions at the installation location never exceed the speci

ﬁ

cations of

the AsteRx-U3.

•

Cover all unused connectors with caps. If the receiver is exposed to marine atmosphere
or high humidity, apply dielectric grease to all connectors.

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды