SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 38

Страница: 38 / 83

4.1. HOW TO CONFIGURE THE ASTERX-U3 FOR RTK

Step 2: Con

ﬁ

gure the cellular modem

Insert a SIM card into the front-panel slot of the AsteRx-U3 as shown in Figure 2-3 while the
unit is powered down.

The on-board cellular modem of the AsteRx-U3 can be con

ﬁ

gured in the

Communication,

Cellular

window as shown in Figure 4-5. A PIN number may or may not be required

depending on the SIM con

ﬁ

guration. In the

Cellular Con

ﬁ

guration

ﬁ

eld, the Access Point

Name (APN) should be inserted with other

ﬁ

elds being optional.

Figure 4-5:

Con

ﬁ

guring the cellular modem

Click on Ok and if the settings are correct, the cellular graphic should appear as shown in
Figure 4-6. The connection type may appear as HSUPA, HSPA or in this example LTE.

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды