SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 27

Страница: 27 / 83

3.4. HOW TO CONFIGURE SBF AND NMEA OUTPUT

3.4.2 Output over Ethernet

SBF and NMEA data can be sent over an Ethernet connection to the AsteRx-U3.

Step 1: Con

ﬁ

gure an IP connection on the AsteRx-U3

The Ethernet port settings can be con

ﬁ

gured by selecting

‘

IP Ports

’

from the

Communication

menu.

In the example shown in Figure 3-16, port 28785 has been

con

ﬁ

gured as connection IPS1 in

TCP2Way

mode so data can be received as well as

transmitted over the connection. It is advisable to select a higher-range port to avoid those
reserved for other purposes such as the webserver and FTP. Also, port 28784 is reserved by
default on the AsteRx-U3 for commands.

Note that a new IP port can also be con

ﬁ

gured by followings the sequence of settings for

NMEA output described in

Step 2

Figure 3-16:

Con

ﬁ

gure the TCP/IP server port setting for data output

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды