SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 83

background image

6.2. AIM+: USING THE SPECTRUM ANALYZER TO

DETECT AND MITIGATE INTERFERENCE

6.2.2 Wideband interference mitigation

Wideband interference of GNSS signals can be caused unintentionally by military and civilian
ranging and communication devices. There are also intentional sources of interference from
devices such as chirp jammers. The wideband interference mitigation system (WBI) of the
AsteRx-U3 can reduce the eﬀect of both types of interference on GNSS signals.

Conﬁguring WBI mitigation

The wideband interference mitigation system (WBI) can be enabled by selecting ‘on’ as shown
in Figure 6-5.

Figure 6-5:

Select ‘on’ to enable wideband interference mitigation then ‘OK’ to

apply the new setting.

WBI mitigation in action

The GPS L1 band interference shown in Figure 6-6 is produced by combining the GNSS
antenna signal with the output from an in-car GPS chirp jammer.

Figure 6-6:

Simulated wideband interference in the GPS L1 band using an in-car

chirp jammer.

62

«
...
60
61
62
63
64
...
»

Содержание AsteRx-U3




















































































Отзывы:

Нет отзывов

Похожие инструкции для AsteRx-U3

CoreBuilder 3500

Бренд: 3Com Страницы: 12

Бренд: Samyung ENC Страницы: 64

FTDX 9000 Series

Бренд: Yaesu Страницы: 12

SCD 3390 RDS Challenge 600 CD

Бренд: Grundig Страницы: 28

Бренд: Stabila Страницы: 10

Бренд: Arcam Страницы: 38

Бренд: Xtrend Страницы: 93

Бренд: Icom Страницы: 182

Бренд: Barlow Wadley Страницы: 11

Бренд: Boss Audio Systems Страницы: 23

DEC 664HD/USB/REC

Бренд: Majestic Страницы: 29

Бренд: Harman Kardon Страницы: 12

Бренд: Future light Страницы: 31

Бренд: ASCOM Страницы: 22

Mercury II Digital FTA

Бренд: Fortec Star Страницы: 3

Бренд: Fiio Страницы: 8

C Prox WAVE500-2B

Бренд: Quantek Страницы: 4

Бренд: Alinco Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды