SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 22

Страница: 22 / 83

3.4. HOW TO CONFIGURE SBF AND NMEA OUTPUT

3.4 How to con

ﬁ

gure SBF and NMEA output

The AsteRx-U3 can output position and GNSS data in both standard NMEA format and
Septentrio’s proprietary compact binary format SBF. The following sections detail how to
con

ﬁ

gure connections to other devices in order to send data.

3.4.1 Output over a serial COM connection

The AsteRx-U3 can be connected via a serial COM cable to an RS-232 compatible secondary
device.

Step 1: Con

ﬁ

gure the serial COM port

The COM port of the AsteRx-U3 should be con

ﬁ

gured with the same baud rate and

ﬂ

ow control setting of the coupled device.

These settings can be con

ﬁ

gured via the

‘

Communication

’

tab as shown in Figure 3-9. In this example, COM3 is set with a speed

of 19200 baud.

Figure 3-9:

Con

ﬁ

gure the baud rate and

ﬂ

ow control of the AsteRx-U3

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды