SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 48

Страница: 48 / 83

4.2. HOW TO CONFIGURE THE ASTERX-U3 FOR ATTITUDE

Step 3: Attitude information in SBF and NMEA data

Details on how to output SBF and NMEA data can be found in Section 3.4.

SBF

Attitude information is contained in the SBF blocks

AuxAntPositions

AttEuler

AttCovEuler

and

EndOfAtt

. These blocks are selected automatically when checking the ‘Attitude’ box when

con

ﬁ

guring SBF output via the

NMEA/SBF Out

window as Figure 4-17 shows.

Figure 4-17:

SBF blocks containing attitude information

NMEA

You can output the attitude information from the AsteRx-U3 in NMEA format by selecting
the standard NMEA HDT sentence or the Septentrio proprietary HRP sentence as shown in
Figure 4-18.

Figure 4-18:

NMEA sentences containing attitude information

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды