RST FRC-F Series Скачать руководство пользователя страница 67

Страница: 67 / 140

9.581.140-6

Page:

If both codes entered match, a corresponding message will be displayed
and the code will be activated.

Otherwise, an error message will be displayed and the code entered will
be rejected.

Enter code "0" to switch off the code check. You can use any code value other than "0".

When the unit leaves the factory, it is not code-protected.

9.5.2 Setting the language

Here, you can set the language to be used for all texts and messages on
the display.

The selected language is activated by pressing the

"E"

key.

Currently, the following languages are supported:

- German

- English

- Turkish

- Spanish

- Czech

- Polish

- Greek
- Hungarian
- Croatian

Codenumber
ok...
----------------------

○

Codenumber
Error
----------------------

○

System
Language
----------------------

○

Language
German
----------------------

○

Содержание FRC-F Series













































































































































Результаты поиска

Содержание FRC-F Series

Отзывы:

Бренды по названию

Популярные бренды

RST FRC-F Series, Руководство пользователя

Результаты поиска

Содержание FRC-F Series

Отзывы:

Бренды по названию

Популярные бренды