RR Mechatronics STARRSED TL Скачать руководство пользователя страница 128

Страница: 128 / 137

E36: No ACK/NACK received after

sending 'Sample result string'!

No response from Host within a certain

time limit after 3 attempts.

See E30

E37: NACK received from host after

sending 'Sample result string'!

Did not receive ACK from Host after

sending 'Sample result string' 3 times.

See E30

E104: Needle unit not in home

position!

Could not start the position motor,

because the needle is not its home

position

•

Check needle home sensor.

•

Faulty needle motor.

•

Faulty Sample probe motor.

•

Check if needle is blocked.

•

Faulty motor driver on the

needle board.

E116-118

Quality Control Errors

See section

Quality control

troubleshooting

E220: TLAX Communication error!

Communication lost between

Computer and TLAX robot unit

•

Check connections settings in

the software.

•

USB cable to master PCB not

connected.

•

No power on one of the TLAX

PCB's.

•

Faulty TLAX PCB(s).

E221: No response from LAS system!

LAS system did not response to a

message from Starrsed TL

•

Check communication cable

between Starrsed TL and the

LAS system.

•

Check serial port settings.

E222: NACK received from LAS system

after sending "Status" message

LAS system rejected “Status” message

from Starrsed TL

See E221

E223: NACK received from LAS system

after sending "Transfer IN in Progress"

message!

LAS system rejected “Transfer IN in

Progress” message from Starrsed TL

See E221

E224: NACK received from LAS system

after sending "Transfer IN Completed"

message!

LAS system rejected “Transfer IN

Completed” message from Starrsed TL

See E221

E225: NACK received from LAS system

after sending "Transfer OUT in

Progress" message!

LAS system rejected "Transfer OUT in

Progress” message from Starrsed TL

See E221

E226: NACK received from LAS system

after sending "Transfer OUT

Completed" message!

LAS system rejected “Transfer OUT

Completed” message from Starrsed TL.

See E221

Appendix for Interrliner

128

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды