RR Mechatronics STARRSED TL Скачать руководство пользователя страница 131

Страница: 131 / 137

E251: Timeout while preparing to open

gripper!

Timeout in ‘prepare to open’-routine.

•

Faulty gripper ‘close’-sensor

detection.

•

Faulty internal mechanics of

the gripper.

•

Faulty gripper motor.

•

Faulty TLAX PCB(s).

•

E252: Timeout while opening gripper!

Timeout in ‘open’-routine.

•

Faulty gripper ‘open’-sensor

detection.

•

Faulty internal mechanics of

the gripper.

•

Faulty gripper motor.

•

Faulty TLAX PCB(s).

E253: Timeout while closing gripper!

Timeout in ‘close’-routine.

•

Faulty gripper ‘close’-sensor

detection.

•

Faulty internal mechanics of

the gripper.

•

Faulty gripper motor.

•

Faulty TLAX PCB(s).

E254: Error while preparing to open

gripper!

Error in ‘prepare to open’-routine.

•

Faulty gripper ‘close’-sensor

detection

E255: Error while opening gripper!

Error in ‘open’-routine.

•

Faulty gripper ‘open’-sensor

detection.

•

Faulty internal mechanics of

the gripper.

•

Faulty gripper motor.

•

Faulty TLAX PCB(s).

E256: Error while closing gripper!

Error in ‘close’-routine.

•

Faulty gripper ‘close’-sensor

detection.

•

Faulty internal mechanics of

the gripper.

•

Faulty gripper motor.

•

Faulty TLAX PCB(s).

•

E257: Error while picking up a tube!

Something went wrong while picking

up a tube. Clear this error to see the

specific error prior to this error.

•

Clear error to see specific

error.

Appendix for Interrliner

MRN-164_2-EN Version 1.08 Starrsed TL

131

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды