RR Mechatronics STARRSED TL Скачать руководство пользователя страница 66

Страница: 66 / 137

Maintenance

The

Interrliner

is an analyzer that operates with considerable amounts of whole blood virtually undiluted,

and stores it in a pipette for one hour. For this reason instrument maintenance is of the utmost importance.
To maintain the maximum reliability of the instrument, the maintenance procedures must be strictly

followed. All procedures are based on a number of samples.

Maintenance levels

(WI

) Work instruction

Daily

WI-231

Daily maintenance

Weekly

WI-232

Weekly maintenance

Level 4 Maintenance

WI-233

Level 4 maintenance

Level 3 Maintenance

WI-234

Level 3 Maintenance

Level 1/2 Maintenance

By service technician

WARNING!!!

Always be aware of the danger of infection, especially during maintenance. Take

appropriate precautions. There is blood involved and therefore a

BIO HAZARD

10.1 - Daily

The purpose of the daily maintenance is to keep the instrument clean and contamination as low as possible.

Clean all parts that are exposed to blood, wipe the outer surface and the stainless steel plate below the

pipette belt. See

WI Daily maintenance

10.2 - Weekly

The purpose of the weekly maintenance is to carry out the daily maintenance and additionally check the

sensors, inspect the sample needle and the vacuum pressure.

Detailed instructions of this procedure can be found in the Work Instruction

Weekly maintenance.

Maintenance

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды