RR Mechatronics STARRSED TL Скачать руководство пользователя страница 127

Страница: 127 / 137

E13: Fillnozzle not in home position!

Fill nozzle did not reach the Home

position within a certain time limit.

•

Fill nozzle motor is faulty.

•

Fill nozzle motor driver on

nozzle board is faulty.

•

Fill nozzle is blocked.

E14: Needle motor position error!

(home)

Needle did not reach the home (top)

sensor within a certain time limit.

•

Check home sensor.

•

Needle motor is faulty.

•

Needle motor driver on

needle board is faulty.

•

Needle is blocked.

E18: Carousel position error! Check

Rinse position.

Value of potentiometer does not match

the value stored in memory of the

current rinse position.

•

Check if the rinse position is

right.

•

Set correct rinse position and

perform a "".

•

Check mechanical connection

potentiometers.

E19: Drive motor timeout!

Drive motor did not move or motor is

blocked

•

Check the home sensor

•

Motor is faulty

•

Motor driver on drive board is

faulty

E29: Result path not found. Switched

to default (D:\). Check "Result Path"

setting.

Selected result path is not valid.

Software is using the default setting

•

Check result path setting

•

Check if network or USB

devices are used.

E30: No ACK/NACK received from host

after sending inquiry!

No response from Host within a certain

time limit after sending an inquiry 3

times.

•

Check communication cable

between Host and Interrliner

computer.

•

Check serial port settings

(baud rate, etc...)

•

Check protocol settings.

•

Check Host computer.

E31: NACK received from host after

sending inquiry!

Did not receive ACK from Host after

sending inquiry 3 times.

See E30

E32: LIMS Connection timeout. Host

not found!

The ESR analyser unit could not

establish a connection with the HOST

(server) via TCP/IP.

•

Check TCP/IP settings

•

Check network cable

•

Check HOST settings

E34: No response from host after

sending 'Sample data record'!

No response from Host within a certain

time limit after 3 attempts.

See E30

E35: No response from host after

sending 'Sample flag record'!

No response from Host within a certain

time limit after 3 attempts.

See E30

Appendix for Interrliner

MRN-164_2-EN Version 1.08 Starrsed TL

127

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды