RR Mechatronics STARRSED TL Скачать руководство пользователя страница 50

Страница: 50 / 137

▪

Check Flow sensor: Click the Check button, the OK sign is shown if the sensor value is in range.

▪

Check liquid sensor: Press test. When test is finished, the OK signs are shown at Rinse and Drain if the

liquid sensor is active.

▪

Check Measure sensor:

Clean sensor first before executing this function.

Click the Check button, the OK sign is shown if the sensor value is in range.

Press the button

Measure

. The pipette currently at the measure position will be measured.

The results are displayed in graphical form:

Measure head start

position correct

Measure head start

position wrong

NOTE:

When a test pipette is installed at the measuring position the result of the test pipette is displayed in the

field "ESR (mm)".

When the sensor is out of range and a red "X" is shown, the sensor values can be

checked by turning on the service mode.

Starrsed TL program

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды