RR Mechatronics STARRSED TL Скачать руководство пользователя страница 24

Страница: 24 / 137

5. Settings screen
6. Service screen

The above picture is an example of the

Sample

screen of the ESR analyser unit in the normal operation

mode. If the software is set to service mode is this indicated with a yellow bar next to the menu.

When the ESR analyser unit is running in the Service mode all kinds of settings can be changed and the

instrument will run with the changed settings. For instance, when ESR time is set to 12 minutes, the

Carousel will move according this time setting to be in time at the measure position.

Do not

perform normal sampling when Service mode is activated.

When the ESR analyser unit is running in the NORMAL MODE, the instrument uses the standard saved

settings. For instance the ESR time is set back to 60 minutes or 30 minutes according the used method.

The User Manual button is at the bottom of the menu. Click this button to open the Interrliner User manual.
When the ESR analyser unit is running on manual mode this is indicated.

Do not open the safety cover during sampling! Some components are moving to another

position before operation finally stops and sample mode is automatically switched OFF.

Switch "

Sample mode

" always OFF before opening the cover for any reason.

Starrsed TL program

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды