RR Mechatronics STARRSED TL Скачать руководство пользователя страница 132

Страница: 132 / 137

E258: Error while placing a tube!

Something went wrong while placing a

tube. Clear this error to see the

specific error prior to this error.

•

Clear error to see specific

error.

E259: Gripper tube detect sensor or

gripper tube end sensor already

triggered!

Not possible to pick up a tube, the

gripper tube detect sensor or the

gripper tube end sensor was already

triggered.

•

Faulty gripper tube hat

adjustment.

•

Faulty gripper sensor(s).

E260: After picking up a tube, gripper

tube end sensor still triggered!

After picking up a tube, the gripper

tube end sensor is still triggered.

•

Faulty gripper tube hat

adjustment.

•

Faulty gripper end sensor.

E261: Tube is still present at the

concerning location (cap could be

removed from tube)!

After picking up a tube, the tube is still

present at the concerning location.

Warning: the cap could be removed

from the tube!

•

Location holds the tube too

strong.

•

Incorrect tube (e.g. diameter

too big).

•

Faulty position calibration

(incorrect depth).

•

Faulty tube detect sensor at

the concerning location.

E262: Tube not present in gripper !

After trying to pick up a tube, the tube

is not present in the closed gripper.

Tube maybe lost or still at the

concerning location.

•

Faulty gripper sensor(s).

•

Faulty internal mechanics of

the gripper.

•

Faulty position calibration

(incorrect depth).

•

Tube lost.

E263: Tube too high in gripper before

placing!

The gripper tube end sensor was

triggered too soon while placing a

tube. Another tube may already be

present at the concerning location

(tube on tube).

•

Tube stuck in gripper.

•

Tube on tube.

•

Faulty gripper tube hat

adjustment.

•

Faulty gripper sensor(s).

E264: Not possible to place a tube,

already another tube present!

Not possible to place a tube at the

concerning location, another tube is

already present at that location.

•

Remove tube at concerning

location.

•

Faulty tube detect sensor at

the concerning location.

E265: Still tube detected in gripper

after placing!

After placing a tube, the gripper tube

detect sensor or the gripper tube end

sensor is still triggered. Tube may still

be in the gripper.

•

Faulty gripper sensor(s).

•

Faulty internal mechanics of

the gripper.

•

Tube stuck in gripper.

E266: Tube not present at location

after placing!

After placing a tube, the tube is not

present at the concerning location.

Tube maybe lost or still in the gripper.

•

Faulty tube detect sensor at

the concerning location

•

Tube lost.

•

Tube stuck in gripper.

Appendix for Interrliner

132

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды