Ronde & Schwarz 1424.6721K02 Скачать руководство пользователя страница 5

Страница: 5 / 148

Contents

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

8.5.5

Configuring the trigger...................................................................................................54

8.6

Configuring results..................................................................................................... 59

8.6.1

Setting the power unit................................................................................................... 59

8.6.2

Setting the result format................................................................................................ 60

8.7

Configuring the measurement modes...................................................................... 61

8.7.1

Continuous average measurement............................................................................... 61

8.7.2

Burst average measurement.........................................................................................65

8.7.3

Timeslot measurement..................................................................................................66

8.7.4

Trace measurement...................................................................................................... 68

8.8

Configuring basic measurement parameters...........................................................73

8.8.1

Configuring auto averaging........................................................................................... 73

8.8.2

Setting the frequency.................................................................................................... 77

8.8.3

Excluding intervals........................................................................................................ 77

8.8.4

Configuring corrections................................................................................................. 78

8.9

Querying measurement results................................................................................. 94

8.10

Calibrating, zeroing.....................................................................................................95

8.11

Testing..........................................................................................................................97

8.12

Configuring the system.............................................................................................. 98

8.12.1

Configuring general functions....................................................................................... 98

8.13

Using the status register.......................................................................................... 106

8.13.1

General status register commands............................................................................. 107

8.13.2

Reading the CONDition part....................................................................................... 107

8.13.3

Reading the EVENt part..............................................................................................108

8.13.4

Controlling the ENABle part........................................................................................ 108

8.13.5

Controlling the negative transition part........................................................................108

8.13.6

Controlling the positive transition part......................................................................... 109

9 Performing measurement tasks - programming examples............110

9.1

Performing the simplest measurement...................................................................110

9.2

Performing the fastest measurement in continuous average mode.................... 110

9.2.1

Untriggered fast unchopped continuous average measurement.................................110

9.2.2

Triggered fast unchopped continuous average measurement.................................... 112

9.3

Performing a buffered continuous average measurement................................... 113

9.4

Performing trace measurements............................................................................. 115

Содержание 1424.6721K02





















































































































































Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды

Ronde & Schwarz 1424.6721K02, Руководство пользователя

Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды