Ronde & Schwarz 1424.6721K02 Скачать руководство пользователя страница 103

Страница: 103 / 148

Remote control commands

R&S

NRP18S-xx

103

User Manual 1178.3686.02 ─ 07

Example:

SYST:LED:MODE USER

Sets the system status LED operating mode to user.

SYST:LED:COL #H01a00000

The LED flashes slowly in red.

SYSTem:LED:MODE SENSor

Sets the system status LED operating mode back to the sensor
internal settings.

SYSTem:LED:MODE

<mode>

Sets whether the color of the system status LED is controlled by the power sensor firm-
ware or by the user settings.

For more information, see

SYSTem:LED:COLor

Parameters:

<mode>

USER | SENSor
*RST:

SENSor

SYSTem:MINPower?

Queries the lower power measurement limit.

This value changes if

[SENSe<Sensor>:]CORRection:SPDevice:STATe

is set to

. The lower measurement limit refers to the sensor or to the combination of a sensor

and the components connected ahead of it.

Use this query to determine a useful resolution for the result display near the lower
measurement limit.

Usage:

Query only

SYSTem:PARameters?

Returns an XML-output containing all commands with the following information, if avail-
able for the command:

●

Default value

●

Minimum value

●

Maximum value

●

Parameters

●

Limits

Each command is shortened to a command token, consisting only of the mnemonics
short form. For example,

CALibration:DATA

is shortened to

CALDATA

as command

token.

Usage:

Query only

Configuring the system

Содержание 1424.6721K02





















































































































































Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды

Ronde & Schwarz 1424.6721K02, Руководство пользователя

Результаты поиска

Содержание 1424.6721K02

Отзывы:

Бренды по названию

Популярные бренды