manualshive.com logo in svg

Ronde & Schwarz 1424.6721K02, Руководство пользователя

Поделиться
Скачать
Ronde & Schwarz 1424.6721K02 Скачать руководство пользователя страница 34

Replacing an R&S

 

NRP

‑

Zxx with an R&S NRP18S-xx

R&S

®

NRP18S-xx

34

User Manual 1178.3686.02 ─ 07

7

 

Replacing an R&S

 

NRP

‑

Zxx with an R&S

NRP18S-xx

The R&S NRP18S-xx power sensors are compatible with the R&S

 

NRP

‑

Zxx series of

power sensors.

R&S

 

NRPxx power sensor

Replaces R&S

 

NRP

‑

Zxx power sensor

R&S

 

NRP18S-10

R&S

 

NRP-Z22

R&S

 

NRP18S-20

R&S

 

NRP-Z23

To use the new power sensors, it can be required to update the drivers. For computer-
based software applications (R&S

 

NRPV and R&S

 

Power Viewer), install the latest

R&S

 

NRP Toolkit (V

 

4.20 or higher).

For using the sensors with base units, signal generators, spectrum analyzers or other
Rohde & Schwarz instruments, install the latest firmware version.

7.1

 

Important difference

After powering the R&S NRP18S-xx , the firmware is loaded. Because the USB power
sensors are plug-and-play devices, the drivers are loaded after enumeration in the host
system. For the R&S

 

NRP

‑

Zxx power sensors, the whole process takes 4

 

s to 5

 

s. For

USB power sensors, the process can take up to 8

 

s.

Otherwise, the R&S

 

NRP

‑

Zxx power sensors and the USB power sensors are compati-

ble as far as possible.

7.2

 

Prerequisites

Install the R&S

 

NRP Toolkit V

 

4.20 or higher, see 

Chapter 5.1, "R&S

 

NRP Toolkit"

,

on page 22.

The new version of the R&S

 

NRP Toolkit is compatible with both the R&S

 

NRP

‑

Zxx

and the R&S NRP18S-xx so that its installation does not affect the usage of the
R&S

 

NRP

‑

Zxx.

After the new version of the R&S

 

NRP Toolkit is installed, you can connect the R&S

NRP18S-xx to the computer and use it with Rohde & Schwarz software applications or
your own programs. For information on Rohde & Schwarz software applications, see
the release notes and the manual of the software application.

Prerequisites

Содержание 1424.6721K02





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды