Rockwell ArmorStratix 5700 series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 548

background image

Rockwell Automation Publication 1783-UM007F-EN-P - September 2016

69

Get Started

Chapter 2

With firmware revision 2.001 or later, the firmware is installed to the running
nonvolatile memory location:

• If you start the switch with the SD card inserted, the firmware is

installed on the SD card.

• If you start the switch from internal memory without the SD card

inserted, the firmware is installed in the internal memory.

When the update process completes, a success message appears, and the switch
automatically restarts. It can take a few minutes for the switch to restart with
the new firmware.

Verify that the latest firmware revision on the switch appears in the Software
field in the Switch Information area of the dashboard.

For more information, see the online help for Device Manager.

Cisco Network Assistant

Cisco Network Assistant is a web interface that you download from Cisco’s
website and run on your computer. It offers advanced options for configuring
and monitoring multiple devices, including switches, switch clusters, switch
stacks, routers, and access points.

Follow these steps to use the software.

1. Go to

http://www.cisco.com/go/NetworkAssistant.

You must be a registered user, but you need no other access privileges.

2. Find the Network Assistant installer.

3. Download the Network Assistant installer, and run it.

You can run it directly from the web if your browser offers this choice.

4. When you run the installer, follow the displayed instructions.

5. In the final panel, click Finish to complete the Network Assistant

installation.

For more information, see the online help for Network Assistant.

IMPORTANT

Wait for the update process to complete. Do not use or close the browser

session with Device Manager active. Do not access Device Manager from
another browser session.

«
...
67
68
69
70
71
...
»

Содержание ArmorStratix 5700 series





































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ArmorStratix 5700 series

RackSwitch G8332

Бренд: IBM Страницы: 18

BNI IOL-314-S52-P012

Бренд: Balluff Страницы: 22

Бренд: FAAC Страницы: 2

Бренд: Rack World Страницы: 4

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

Бренд: Handic Страницы: 2

Бренд: Waters Network Systems Страницы: 16

EtherDevice EDS-4009 Series

Бренд: Moxa Technologies Страницы: 18

Бренд: TP-Link Страницы: 2

3C17205 - SuperStack 3 Switch 4400 PWR

Бренд: 3Com Страницы: 90

BNI EIP-950-000-Z009

Бренд: Balluff Страницы: 12

Бренд: StarTech.com Страницы: 16

Бренд: Uniclass Страницы: 32

Бренд: Alloy Страницы: 33

Бренд: enbrighten Страницы: 2

Бренд: Icy Box Страницы: 12

Бренд: Good Way Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды